Ax-4280 manual

The trap bottle is also attached here. Washing solution joint W Connect the tube from the washing solution bottle here. Washing solution sensor terminal Connect the liquid sensor cord of the washing solution bottle here. Hand-held barcode reader terminal Connect the optional hand-held barcode reader here. Cooling fan The fan draws in air from outside to cool the inside of the instrument. Main power switch Press this switch to turn on or off the main power supply.

Keep this switch on for daily use, and turn it off when cleaning specific components or during long-term disuse. Power input terminal Connect the power cord which came with the instrument here. Install the instrument under the supervision of a serviceperson.

It is dangerous to handle the instrument with the covers open. High voltage parts are located inside. These factors may cause incorrect measurement results, as well as deformation of or damage to the instrument. Remove these retainers before installing the instrument.

Feeder protective cover 2 Open the maintenance cover. Side cover Maintenance cover AX NOTE: Lower the auxiliary legs of the sampler until they contact the countertop.

Unless the sampler is stable, it can deform under its own weight and the samples and the nozzle can be damaged. Lower all three legs to the countertop. The sampler is unstable on just one or two auxiliary legs.

Prepare the washing solution. If higher than the instrument base, liquid waste may not drain properly and consequently leak. Contacting liquid waste with unprotected hands may expose you to pathogenic microbes.

Pull out the waste box tray. Waste box tray Install the waste box. Prepare: Power cord and, if necessary, communication cable for the external device Use the specified RSC cross cable or Ethernet cable to connect an external device to the instrument.

How to turn off the power is also explained at the end of this section. Please wait Prepare: Thermal printer paper Load the thermal printer paper. Moving the instrument with washing solution in the flow line may damage the instrument.

Check for used test strips. Discard used protective gloves and liquid waste in accordance with local regulations for biohazardous waste. Earth line Earth anchoring screw 2 Insert the tip of a Phillips screwdriver in the screw holes on the splash guard to loosen the two screws inside.

This section describes basic instructions you should learn in order to run urine tests and make parameter settings. Strip S. Cal depending on the status of the instrument. An ID can contain up to 18 digits, and include numbers, alphabetic characters case sensitive , and hyphens -. Check for used test strips and liquid waste. Check the washing solution and printer paper. Press standby switch to power on.

Standby screen An ID can contain up to 18 digits and can include numbers, alphabet and special characters see page This means a maximum of samples can be measured continuously. To have the built-in barcode reader read barcodes, place the labels in the correct position on the tubes. STAT measurement requires samples to be loaded into ports 1 to 7, and control measurement requires controls to be loaded into ports 8 to When you use the instrument for the first time, read through these sections before start measurement.

This instrument uses urine as sample and as an ingredient of control solution. Urine may be contaminated by pathogenic microbes that can cause infectious diseases. Carefully read the package insert and observe the expiration date. Default settings have been made when shipped from the factory, and you can change the settings as you need.

Measurement start Determines whether sequential measurement Continue from number assignment numbers are assigned through batches, or the previous batch measurement number is reset at the beginning of each batch. Measurement number Determines whether measurement numbers Then, load the correct test strips into the feeders. Desiccant bag 3 Take out a desiccant bag from the test strip bottle When loading strips and attach it to the feeder cover.

This allows the instrument to automatically eject appropriate test strips from the assigned feeder for measuring samples in the item rack. Start the normal measurement. To return to the [Measuring You may use the STAT port when you have only one sample to measure, or when you are asked to measure a new sample urgently while normal measurement is in progress.

This is accomplished by loading the higher priority samples into the STAT and control rack and placing the rack between the sample racks currently loaded in the sampler. If you use the test strips in the main feeder, skip this step and go to step.

The main feeder is indicated by a light blue background on the standby screen. How the STAT measurement takes place depends on the status of the instrument. If the instrument is on standby: Measuring Page S. Calibration Perform S. Please ensure the urinometer conforms to the Brix — S.

Ensure the liquid level is at least 40 mm above the bottom of the tube. Page Starting S. Calibration Access the S. Cal Ready for measurement screen. Prepare S. Up to 3 types or concentrations of controls can be measured by loading them into the STAT and control rack control measurement can be performed using at least one control, and does not always require three different controls.

REFERENCE: In the case that control measurement was carried out at the beginning or in course of normal measurement, normal measurement will start or resume at this point. The check strip container holds two gray strips and two white strips. Use a pair of white and gray strips for check measurement at a time. Reflectivity label Measure the first check strip white. Print Check measurement Measurement completed. If the results are: Within range: The instrument is working correctly.

However, the check strips used for the first check measurement are abnormal. See the following figure for information on what the printed results report includes. The exclamation mark flag has a higher priority than the asterisk flag. The S. AX Example Product name and software version AX V If the memory becomes full, the oldest data is replaced with the latest one. This can be replaced with "Transmit ". Request Parts. Add to My Bench.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Please review our Privacy Policy for more details. I Agree. Site Links. Subscribe To eNews. Grasso 9 years ago 9 years ago link error How to solve a "Link Error"? Local pickup is available for those arranging their own freight carriers and direct customer pick up.

Contact us for a quote for international shipments. Specific gravity is determined by the refractive index method. Available Documentation manual etc. After the development of this, ARKRAY continued to specialize in fully-automated urine analysis and continued to work to provide added values to its customers. For high value and high sensitivity items that require special packaging, we use several layers of bubble wrap and shrink wrap to seal the product in a protective bubble so the product always arrives in the mas in which you purchased it.

If this action is too quick, filter pads become separated from the base film and the test strip becomes useless. If you have forgot password please click here. Inventory and Ecommerce Management. The basic principle of the feeder has not changed over the past 30 years. However, there was a disadvantage with the air-segment method.

Vonderschmitt Journal of clinical chemistry and clinical…. Multi-centre evaluation of the urine test strip analyser Rapimat.

Evaluation of Aution Max AX automated urine test-strip analyser. Sale is for imaged item only 2. This includes personalizing content and advertising. The table moves from left to right allowing the test strip to easily enter the groove and is fed under a dividing wall in the reagent housing, making sure that only a single test strip is offered up at a time.

If customers will require packaging for local pickup or shipping arrangements, New Life Scientific can provide packaging.